Page Confirming Module Supervision 6. Continue this procedure at each keypad until all have If a module is connected but does not show as being present, it may be due to any of the following reasons: been assigned to the correct slot and partition.
Page Section 3: How To Program Section 3: How to Program The following section of the manual describes how to The following table indicates which number should be enter Installer Programming and how to program the var- pressed to enter the corresponding Hex digit: ious sections.
Page Viewing Programming 3. When a programming section is entered, the keypad will immediately display the first digit of information programmed in that section. The keypad displays the information using a binary for- mat, according to the following chart: See Hex data entry instructions The LED keypad uses function and zone indicator lights to represent alarm functions and status. The LCD keypad provides a written description on the liquid crystal display and uses function indicator lights to communicate alarm status to the user.
Page Commands The keypad will display the event number, partition, time If the Code Required for Bypass option is enabled, the and date of the event in question. See section 4. Paragraph 5. Table references the paragraphs in this section with the corre- sponding location in the programming worksheets. Page For The Record 5. Remove these pages and retain for reference.
Telephone Line Monitor disabled. The TLM function will be shut off and telephone line troubles will not be indicated by the system. The system will verbally annunciate the zone or programmed label when it is violated if Door Chime is programmed. This feature is available when Escort TC v3.
Page 38 []-[] - Alarm Reporting Codes, Zones this reporting code will be sent Auxiliary Input Alarm: when PGM2 is being used for 2-wire smoke detectors and The panel will transmit the Zone Alarm reporting code for the 2-wire smoke detector goes into alarm. Page 42 pad while the system is armed. After each dialing attempt, the communicator switches between the 1st phone number and 3rd phone number.
Call 1st Number, Backup to 3rd Number. If the programmed number of attempts to commu- nicate to the First Telephone Number fail, the same number of attempts will be made to com- municate to the Third Telephone Number. Output Level The output will activate switch to Ground when the event occurs. Page Special Installer Instructions 1. PC Programming Section [] buffer.
Check the event buffer to ensure that all zones and FAP keys are functioning properly. Fire moni- toring zone programming is the same as burglary zone programming. Page Pc Zones 7. Page Section 9: Listing Requirements The digital communicator must be enabled.
Page Using Advanced Functions Section 4: Using Advanced Functions This section describes how to perform more specialized functions: bypassing zones, turning the door chime on or off, viewing the trouble display and event buffer, and testing your system. NOTE: Your system may have cross zoning enabled. For more information, ask your installer.
Press Zones 2. Press 3. To exit bypassing mode and return to the Ready state, press Bypass A Bypass Group is a selection of zones programmed into the system. If you bypass a group of zones on a regular basis, you can program them into the Bypass Group, so that you do Groups not have to bypass each zone individually every time.
Page Identifying Trouble Conditions Identifying Your system continuously checks for a number of possible trouble conditions. To exit trouble viewing, press Viewing the The event buffer will show you a list of the last events that have occurred on your sys- tem. You must use an LCDZ keypad to view the event buffer.
Event Buffer from an 1. Refer to this section for detailed instructions on: programming access codes, setting the time and date, and adjust- ing the keypad sounders and lights. Programming The master code code 40 can be used to program system options, arm and disarm the sys- Access Codes This is important for the auto-arm feature to function correctly, and for accurate reporting of events. Time and Date 1. Press 2. Page Fire Safety Read this section carefully for important information about fire safety.
Household Most fires occur in the home. To minimize this danger, we recommend that a household fire safety audit be conducted and a fire escape plan be developed.
Fire Safety 1. Page Glossary Access code A 4- or 6-digit code that allows access to arming, disarming and other system functions. Alarm When a zone is violated e. Intrusion burglary alarm: An alarm triggered by an intrusion detector e.
Page 28 Exit delay A timer programmed by your installer. It starts when you arm your system, to allow you a period of time in which to leave the premises. At the end of the exit delay, the system will be armed. Master code The master code is a 4- or 6- digit access code that is used to program system options, to arm and disarm the system, and to program other access codes.
Page System Information Section 8: System Information Fill out the following information for future reference and store this guide in a safe place. During the warranty period, Digital Security Controls Ltd.
As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system. This certifi- cation means that the equipment meets certain telecommunications network pro- tective, operational and safety requirements. This manual is also suitable for: Pc Power - rev2 Print page 1 Print document 36 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals?
Sign In OR. Don't have an account? Sign up! Restore password.
0コメント